103 questions
240
views
1
answer
2
votes
2015-03-04 14:40:18 -0500 Jamie Bull 
How do I manually adjust thermostat settings in the IDF editor?
4.6k
views
5
answers
7
votes
2022-06-07 10:13:38 -0500 obuchely 
Thermal Load too low in the OpenStudio / EnergyPlus
377
views
2
votes
2015-03-24 03:50:58 -0500 Julien Marrec 
How to simulate only one zone
1.6k
views
1
vote
2015-04-15 03:02:54 -0500 Julien Marrec
Determining the Heating and Cooling Loads for each zone
1.6k
views
8
votes
Cooling & Heating Component Breakdown with OpenStudio/EnergyPlus
794
views
2
votes
2015-06-28 14:53:43 -0500 crduggin 
Linking model to Suncast, Macroflo and ApacheHVAC
439
views
3
votes
2015-07-01 07:59:24 -0500 JustinShultz
Clarification of EnergyPlus OtherEquipment Impact on HVAC Loads
1.9k
views
6
votes
Energyplus design cooling load is zero
6.8k
views
6
votes
How to calculate heating load based on heating degree hours?
188
views
1
answer
4
votes
heating energy when changing cooling setpoint temperature
2k
views
3
answers
10
votes
Best output:variable for zone heating / cooling load
281
views
1
vote
2016-03-01 08:15:59 -0500 Julien Marrec
Heating and cooling loads for the southern hemisphere
2k
views
2
votes
Unreasonable heating/cooling loads results [closed]
638
views
1
answer
-2
votes
disproportionately heating loads results
347
views
2
votes
2016-04-23 13:13:22 -0500 rraustad
Space heating and DHW energy consumption results
1.2k
views
3
votes
2016-05-09 09:36:58 -0500 Pouya 
lower u-value with higher cooling energy?
1.8k
views
-1
votes
2016-05-23 02:53:52 -0500 Julien Marrec
hourly heating and cooling loads for one year
291
views
no
answers
1
vote
2016-05-24 01:11:51 -0500 shahin1992 
Zone predicted sensible load to setpoint heat transfer rate [closed]
578
views
1
answer
2
votes
2016-05-31 09:23:19 -0500 shahin1992
best output variable for latent cooling/Heating ?
114
views
1
answer
2
votes
Transmission losses very low using design builder
254
views
1
answer
3
votes
2017-01-13 09:53:37 -0500 rraustad
Why are my primary heating components not heating to full capacity before secondary components activate?
323
views
no
answers
3
votes
2017-01-25 00:32:34 -0500 Julien Marrec
How to use the results of the predictor in EMS
144
views
2
votes
2017-02-21 05:36:00 -0500 Julien Marrec
Is possible to calculate the heating rate using COMPACT HVAC:ZONE:PURCHASED AIR in Energy Plus v. 8.6?
303
views
1
answer
3
votes
2017-06-26 05:17:20 -0500 Julien Marrec
about getting annual heating and cooling load based on specific location
1.2k
views
2
answers
1
vote
2017-07-14 09:42:48 -0500 rsunnam
why my heating load is too high than cooling load
328
views
1
answer
1
vote
How does EnergyPlus weigh incoming solar radiation?
1.1k
views
2
votes
2017-10-14 20:12:52 -0500 Aaron Boranian
Electrical equipment latent/radiant fraction heating impact
136
views
no
answers
1
vote
Why does adiabatic boundary condition result in zero heating loads?
401
views
2
votes
2017-12-11 04:20:52 -0500 jack_l 
determining heating and cooling in peak conditions
1.3k
views
1
answer
1
vote