Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture:

Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tried to resolve that error by applying the following potential resolutions, but non of them worked:

1. Incresed DHW loop setpoint temperature using SetpointManager:Scheduled
2. Increased Water Heater Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad

Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture:

Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tried to resolve that error by applying the following potential resolutions, but non of them worked:

1. Incresed DHW loop setpoint temperature using SetpointManager:Scheduled
2. Increased Water Heater Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad

Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture:

Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tried to resolve that error by applying the following potential resolutions, but non of them worked:

1. Incresed DHW loop setpoint temperature using SetpointManager:Scheduled
2. Increased Water Heater Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad

Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture:

Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tried to resolve that error by applying the following potential resolutions, but non of them worked:

1. Incresed DHW loop the setpoint temperature SetpointManager:Scheduled
2. Increased Water Heater Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad

Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture:

Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tried to resolve that error by applying the following potential resolutions, but non of them worked:

1. Incresed the setpoint SetpointManager:Scheduled
2. Increased Water Heater Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad

Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture:

Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tried to resolve that error by applying the following potential resolutions, but non of them worked:

1. Incresed the setpoint SetpointManager:ScheduledSetPointManger:Scheduled
2. Increased Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad

Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture:

Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tried to resolve tor esolve that error by applying appying the following potential resolutions, but non of them worked:

1. Incresed the setpoint SetPointManger:Scheduled
2. Increased Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad

Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture:

fixture: Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tried tied tor esolve that error by appying the following potential resolutions, but non of them worked:

1. Incresed the setpoint SetPointManger:Scheduled
2. Increased Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad

Hi,

I was wondering if anyone could help me with the following EnergyPlus question. More specifically, I'm modeling a water heater object for a single-family model (WaterHeater:Mixed). While the model ran successfully, I found the following error, that has repeated for each fixture: Target water temperature should be less than or equal to the hot water temperature error continues... * ~~~ * ...target water temperature = 48.89 C * ~~~ * ...hot water temperature = 47.58 C

I tied tor esolve that error by appying the following potential resolutions, but non of them worked:

1. Incresed the setpoint SetPointManger:Scheduled
2. Increased Maximum Temperature Limit

Any suggestions will be greatly appreciated!

Thanks, Mohammad