I am using v1.14 and trying to model a Fan coil unit with fan operating on a schedule- unfortunately, the osm file does done have supply air fan operating mode field that makes it relevant to operate the unit at that schedule and cycle it per demand at other hours. It is only operating as either run as constant(24X7) or cycling it on demand(OA cycles as well!!!!). How can I get this to work? The following text is from energy plus i had edited to make it work. I prefer to stay in the open studio platform inorder to run parametrics using PAT. Please help!!!!

ZoneHVAC:FourPipeFanCoil,
  Zone HVAC Four Pipe Fan Coil 64, !- Name
  Res Common area(OA), !- Availability Schedule Name
  ConstantFanVariableFlow, !- Capacity Control Method
  Autosize, !- Maximum Supply Air Flow Rate {m3/s}
  1, !- Low Speed Supply Air Flow Ratio
  1, !- Medium Speed Supply Air Flow Ratio
  Autosize, !- Maximum Outdoor Air Flow Rate {m3/s}
  Res Common area(OA), !- Outdoor Air Schedule Name
  Node 571, !- Air Inlet Node Name
  Node 572, !- Air Outlet Node Name
  OutdoorAir:Mixer, !- Outdoor Air Mixer Object Type
  Zone HVAC Four Pipe Fan Coil 64 OA Mixer, !- Outdoor Air Mixer Name
  Fan:OnOff, !- Supply Air Fan Object Type
  Fan On Off 64, !- Supply Air Fan Name
  Coil:Cooling:Water, !- Cooling Coil Object Type
  Coil Cooling Water 64, !- Cooling Coil Name
  Autosize, !- Maximum Cold Water Flow Rate {m3/s}
  , !- Minimum Cold Water Flow Rate {m3/s}
  , !- Cooling Convergence Tolerance
  Coil:Heating:Water, !- Heating Coil Object Type
  Coil Heating Water 64, !- Heating Coil Name
  Autosize, !- Maximum Hot Water Flow Rate {m3/s}
  , !- Minimum Hot Water Flow Rate {m3/s}
  , !- Heating Convergence Tolerance
  , !- Availability Manager List Name
  , !- Design Specification ZoneHVAC Sizing Object Name
  Res Common area(OA); !- Supply Air Fan Operating Mode Schedule Name

I am using v1.14 and trying to model a Fan coil unit with fan operating on a schedule- unfortunately, the osm file does done have supply air fan operating mode field that makes it relevant to operate the unit at that schedule and cycle it per demand at other hours. It is only operating as either run as constant(24X7) or cycling it on demand(OA cycles as well!!!!). How can I get this to work? The following text is from energy plus i had edited to make it work. I prefer to stay in the open studio platform inorder to run parametrics using PAT. Please help!!!!

ZoneHVAC:FourPipeFanCoil,
  Zone HVAC Four Pipe Fan Coil 64, !- Name
  Res Common area(OA), !- Availability Schedule Name
  ConstantFanVariableFlow, !- Capacity Control Method
  Autosize, !- Maximum Supply Air Flow Rate {m3/s}
  1, !- Low Speed Supply Air Flow Ratio
  1, !- Medium Speed Supply Air Flow Ratio
  Autosize, !- Maximum Outdoor Air Flow Rate {m3/s}
  Res Common area(OA), !- Outdoor Air Schedule Name
  Node 571, !- Air Inlet Node Name
  Node 572, !- Air Outlet Node Name
  OutdoorAir:Mixer, !- Outdoor Air Mixer Object Type
  Zone HVAC Four Pipe Fan Coil 64 OA Mixer, !- Outdoor Air Mixer Name
  Fan:OnOff, !- Supply Air Fan Object Type
  Fan On Off 64, !- Supply Air Fan Name
  Coil:Cooling:Water, !- Cooling Coil Object Type
  Coil Cooling Water 64, !- Cooling Coil Name
  Autosize, !- Maximum Cold Water Flow Rate {m3/s}
  , !- Minimum Cold Water Flow Rate {m3/s}
  , !- Cooling Convergence Tolerance
  Coil:Heating:Water, !- Heating Coil Object Type
  Coil Heating Water 64, !- Heating Coil Name
  Autosize, !- Maximum Hot Water Flow Rate {m3/s}
  , !- Minimum Hot Water Flow Rate {m3/s}
  , !- Heating Convergence Tolerance
  , !- Availability Manager List Name
  , !- Design Specification ZoneHVAC Sizing Object Name
  Res Common area(OA); !- Supply Air Fan Operating Mode Schedule Name

I am using v1.14 and trying to model a Fan coil unit with fan operating on a schedule- unfortunately, the osm file does done have supply air fan operating mode field that makes it relevant to operate the unit at that schedule and cycle it per demand at other hours. It is only operating as either run as constant(24X7) or cycling it on demand(OA cycles as well!!!!). How can I get this to work? The following text is from energy plus i had edited to make it work. I prefer to stay in the open studio platform inorder to run parametrics using PAT. Please help!!!!

ZoneHVAC:FourPipeFanCoil,
 Zone HVAC Four Pipe Fan Coil 64, !- Name
 Res Common area(OA), !- Availability Schedule Name
 ConstantFanVariableFlow, !- Capacity Control Method
 Autosize, !- Maximum Supply Air Flow Rate {m3/s}
 1, !- Low Speed Supply Air Flow Ratio
 1, !- Medium Speed Supply Air Flow Ratio
 Autosize, !- Maximum Outdoor Air Flow Rate {m3/s}
 Res Common area(OA), !- Outdoor Air Schedule Name
 Node 571, !- Air Inlet Node Name
 Node 572, !- Air Outlet Node Name
 OutdoorAir:Mixer, !- Outdoor Air Mixer Object Type
 Zone HVAC Four Pipe Fan Coil 64 OA Mixer, !- Outdoor Air Mixer Name
 Fan:OnOff, !- Supply Air Fan Object Type
 Fan On Off 64, !- Supply Air Fan Name
 Coil:Cooling:Water, !- Cooling Coil Object Type
 Coil Cooling Water 64, !- Cooling Coil Name
 Autosize, !- Maximum Cold Water Flow Rate {m3/s}
 , !- Minimum Cold Water Flow Rate {m3/s}
 , !- Cooling Convergence Tolerance
 Coil:Heating:Water, !- Heating Coil Object Type
 Coil Heating Water 64, !- Heating Coil Name
 Autosize, !- Maximum Hot Water Flow Rate {m3/s}
 , !- Minimum Hot Water Flow Rate {m3/s}
 , !- Heating Convergence Tolerance
 , !- Availability Manager List Name
 , !- Design Specification ZoneHVAC Sizing Object Name
 Res Common area(OA); !- Supply Air Fan Operating Mode Schedule Name